Sunday, September 6, 2015

Ip Address Structure, Expilinatin OF IP Address {A short way}



  



IP ADDRESS STRUCTURE:

Note: the terms multicast address and MSB are explained at the end.


Every station on a PSN (packet switched network) that is based on the TCP/IP
protocol (your computer is one, for example. Yes, we're referring to a host
that is connected to the net) must have an IP address, so it can be identified,
and information can be relayed and routed to it in an orderly fashion.



An IP address consists of a 32 bit logical address. The address is divided
into two fields:



1) The network address:


Assigned by InterNIC (Internet Network Information Center).
In fact most ISPs (internet service providers) purchase a number of addresses
and assign them individually.



2) The host address:


An address that identifies the single nodes throughout the network. It can be assigned
by the network manager, by using protocols for it such as DHCP, or the workstation itself.



[The IP networking protocol is a logically routed protocol, meaning that address 192.43.54.2
will be on the same physical wire as address 192.43.54.3 (of course this is not always true. It depends on the

subnet mask of the network, but all of that can fill a text of its own)


IP address structure:


   ---.---.---.---

   ^             ^
   |               |
network    |    host

Every " --- " = 8 bits.
The first bits ===> network address
The last bits  ===> host address.
with 8 bits you can present from 0-255 . (binary=(2 to the power of 8)-1)

Example:
11000010.01011010.00011111.01001010 (binary)
194.90.31.74 (decimal)
IP address CLASSES :
We can classify IP addreses to 5 groups. You can distinguish them by comparing the "High Order" bits (the first four bits on the
left of the address):

type  | model  | target | MSB |addr.range    |bit number| max.stations|
     |        | groups |     |              |net./hosts|             |
------|--------|--------|-----|--------------|----------|-------------|
 A   |N.h.h.h | ALL    |  0  | 1.0.0.0      |   24/7   | 16,777,214  |
     |        | ACCEPT |     |    to        |          |             |
     |        | HUGE   |     | 127.0.0.0    |          |             |
     |        | CORPS  |     |              |          |             |
-----------------------------------------------------------------------
     |N.N.h.h | TO ALL | 10  | 128.1.00     | 16/14    | 65,543      |
 B   |        | LARGE  |     |    to        |          |             |
     |        | CORPS  |     | 191.254.00   |          |             |
-----------------------------------------------------------------------
     |N.N.N.h |TO ALOT | 110 | 192.0.1.0    | 8/22     |  254        |
 C   |        |OF      |     |    to        |          |             |
     |        |SMALL   |     | 223.225.254  |          |             |
     |        |CORPS   |     |              |          |             |
-----------------------------------------------------------------------
D    | NONE   |MULTI-CA|1110 | 224.0.0.0     | NOT FOR |   UNKNOWN   |
     |        |ST ADDR.|     |    to         | USUAL   |             |
     |        |RFC-1112|     |239.255.255.255| USE     |             |
-----------------------------------------------------------------------
E    | NOT FOR|EXPERIME|1,1,1,1| 240.0.0.0     |NOT FOR|  NOT FOR USE|
     |  USE   |NTAL    |       |   to          |USE    |             |
     |        |ADDR.   |       |254.255.255.255|       |             |
-----------------------------------------------------------------------

N=NETWORK , h=HOST .



Notice the address range 127.X.X.X.
These addresses are assigned to internal use to the network device, and are
used as an application tool only. For example: 127.0.0.1, the most common one,
is called the loopback address - everything sent here goes directly back to
you, without even traveling out on the wire.
Also, some IPs are reserved for VPNs - Virtual Private Networks. These are
local area networks over wide area networks that use the Internet Protocol to
communicate, and each computer inside the network is assigned with an IP
address. So, suppose a certain computer wants to send a data packet to
another host on the network with the IP 'x', but there's also another host on
the Internet that has the same IP - what happens now? So this is why you
cannot use these and other forms of reserved IPs on the Internet.

EXTRA:

Distinguishing different groups:

You have to compare the first byte on the left in the address as follows:

 


Type |    First byte  | MSB
    |    in decimal  |
----------------------------
A    | 1-127          | 0
----------------------------
B    | 128-191        | 10
----------------------------
C    | 192-223        | 110
----------------------------
D    | 224-239        | 1110
----------------------------
E    | 240-254        | 1111
----------------------------


NOTES: Yes, we know, we've left A LOT of things unexplained in this teaxt.
With time, we will write more tutorials to cover these and other subjects. So
in the meantime, I suggest that you go to http://blacksun.box.sk, find the
tutorials page and see if there's anything else that's interesting to you.
And remember - we also have a message board, so if you have any questions,
feel free to post them there.


weird shit (newbie note):

1) Multicast: (copied from RFC 1112)
  IP multicasting is the transmission of an IP datagram to a "host
  group", a set of zero or more hosts identified by a single IP
  destination address.  A multicast datagram is delivered to all
  members of its destination host group with the same "best-efforts"
  reliability as regular unicast IP datagrams, i.e., the datagram is
  not guaranteed to arrive intact at all members of the destination
  group or in the same order relative to other datagrams.

  The membership of a host group is dynamic; that is, hosts may join
  and leave groups at any time.  There is no restriction on the
  location or number of members in a host group.  A host may be a
  member of more than one group at a time.  A host need not be a member
  of a group to send datagrams to it.

  A host group may be permanent or transient.  A permanent group has a
  well-known, administratively assigned IP address.  It is the address,
  not the membership of the group, that is permanent; at any time a
  permanent group may have any number of members, even zero.  Those IP
  multicast addresses that are not reserved for permanent groups are
  available for dynamic assignment to transient groups which exist only
  as long as they have members.

  Internetwork forwarding of IP multicast datagrams(ip packets)is handled by
  "multicast routers" which may be co-resident with, or separate from,
  internet gateways.  A host transmits an IP multicast datagram as a
  local network multicast which reaches all immediately-neighboring
  members of the destination host group.  If the datagram has an IP
  time-to-live greater than 1, the multicast router(s) attached to the
  local network take responsibility for forwarding it towards all other
  networks that have members of the destination group.  On those other
  member networks that are reachable within the IP time-to-live, an
  attached multicast router completes delivery by transmitting the
  datagram(ip packet) as a local multicast.

  *if you donot understand the above do not worry, it is complicated and dry
  but reread it and read it again get a dictionary if it helps.
  Hacking is not easy.

2) MSB: Most Significent Bit:
  In set numbers the first number on the left is the most important because it
  holds the highest value as opposed to the LSB=> least significent bit, it
  always holds the the smallest value.

Facebook Twitter Google+ WhatsApp StumbleUpon Pinterest Addthis

MAXIT INTERNET

BLOGGER

CD DVD RW

DELL

DOWNLOAD

FTP Server Linux

HACK

HARD DRIVE

HOW TO WORKIN

HARDWAER

INTERNET

INTERNET CAFE

LAPTOP

LENOVO

LINUX

Additional configuration for Samba Server (Part 2)  

BSNL/Airtel/Idea using Huawei E156G 3g Wireless USB Linux 5   

Basic File Extensions    CHANGING AN ACCOUNT EXPIRATION DATE   

Configure Linux as a Router   

Configure SAMBA Server (Part-1)   

Configure VNC server   

Configure Yum Server (Part-1)   

Configure yum server for Client machine (Part 3)   

Configuring Samba as a Standalone Server (Part 3)  

Connecting ftp Server with Anonymous User Part 5  

Create ftp account with Shared directory Part 3  

DHCP Server Configuration Part 2  

DHCP Server Configuration Part-1  

DHCP Server Configuration Part-3  

Enabling FTP Services in Yum Server (Part 5)  

FTP Server Configuration Part 1  

FTP Server How to Change In Primary DNS Server Part 2  

HTTP Client side configuration (Part 4)  

How to Vsftpd conf files Parameter Part 6   

LINUX FILE SYSTEM STRUCTURE  

Linux User Administrtion  

Linux as a Router configuration for Client Machine   

Linux client machine FileZilla FTP Client Part 4  

Local Yum Server (Part 2)  

Modifying Existing User Information  

Primary DNS Server Configuration Part-1  

Primary DNS Server Configuration Part-2    

Primary DNS Server Configuration Part-3  

Remove Linux From Your Pc Safely and restoring your MBR  

Sharing & Accessing Samba Share (Part 4)   

Speeding up your internet connection under Linux and Windows   

THE ROOT FILE SYSTEM   

VNC Server Configuration

LINUX LAB

Linux as a Router

MOTHERBOARD

Mobile

NETWORKING

REDHAT 5

REGISTRY EDTOR

RESET BIOS PASSWORD

SAMBA Server Linux

SERVER

SERVER CONFIG

SOFTWAER

VNC server Linux

Window 10

Window XP

Follow by Email

MAX-IT INTERNET

MAX-IT INTERNET
TIPS AND TRICKS